鲍明正,祝永坤,吴昊,杨志超,于开文
BAO Mingzheng, ZHU Yongkun, WU Hao, YANG Zhichao, YU Kaiwen

• 1:国网内蒙古东部电力有限公司，呼和浩特 010010

摘要(Abstract)：

针对某±500 kV直流输电线路架空地线悬垂线夹承重轴断裂的问题，结合该线路设计条件及平断面定位图、地形地貌、气象条件等，通过地线悬垂线夹外观、尺寸检查以及金相、硬度检测，对悬垂线夹受力情况进行了全面分析，认为造成地线悬垂线夹承重轴断裂的原因主要为档距比大、风力影响、地形地貌复杂等，并从技术和运维管理方面提出了优化档距、采用耐磨金具等处理建议及防范措施。
In view of the breakage of the load-bearing shaft of a ±500 kV DC transmission line overhead ground wire clamp, combined with the design conditions of the line and the plane cross section diagram, topography and geomorphology, meteorological conditions, etc, through the appearance and size inspection of the ground wire suspension clamp, as well as metallographic and hardness testing, this paper comprehensively analyzes the stress of the suspension clamp, and concludes that the main causes of the load-bearing shaft fracture are large gear ratio, wind influence, complex topography and geomorphology, etc. From the aspects of technology and operation and maintenance management, treatment suggestions and preventive measures such as optimizing the gear span and using wear-resistant hardware.

关键词(KeyWords)： 输电线路;架空地线;风荷载;悬垂线夹;承重轴;磨损
transmission line;overhead ground wire;wind load;suspension clamp;load-bearing shaft;wear

Abstract:

Keywords:

基金项目(Foundation):

作者(Author): 鲍明正,祝永坤,吴昊,杨志超,于开文
BAO Mingzheng, ZHU Yongkun, WU Hao, YANG Zhichao, YU Kaiwen

DOI: 10.19929/j.cnki.nmgdljs.2022.0097

参考文献(References)：

• [1] 董吉谬.电力金具手册.2版[M].北京:中国电力出版社, 2001.
  [2] 全国架空线路(电力金具)标准化技术委员会.悬垂线夹:DL/T 756-2009[S].北京:中国电力出版社, 2009.
  [3] 全国铸造标准化技术委员会.可锻铸铁件:GB/T 9440-2010[S].北京:中国标准出版社, 2011.
  [4] 全国架空线路(电力金具)标准化技术委员会.电力金具通用技术条件:GB 2314-2016[S].北京:中国标准出版社, 2016.
  [5] 全国架空线路标准化技术委员会.电力金具标称破坏载荷系列及连接型式尺寸:GB/T 2315-2017[S].北京:中国标准出版社, 2018.
  [6] 全国钢标准化技术委员会.金属材料:拉伸试验第一部分:室温试验方法:GB/T 228.1-2010[S].北京:中国标准出版社, 2011.
  [7] 全国钢标准化技术委员会.金属材料布氏硬度试验第1部分:试验方法:GB/T 231.1-2018[S].北京:中国标准出版社, 2018.
  [8] 中国电力企业联合会.110 kV~750 kV架空输电线路设计规范:GB 50545-2010[S].北京:中国计划出版社, 2010.
  [9] 国网内蒙古东部电力有限公司.国网蒙东电力风区分布图(2020版)[Z].呼和浩特:国网内蒙古东部电力有限公司, 2020.
  [10] 李亚宁,刘荣海,史腾飞,等.基于有限元的悬垂线夹磨损分析与研究[J].云南电力技术, 2017, 45(5):136-140. LI Yaning, LIU Ronghai, SHI Tengfei, et al. Analysis and research on the wear of Suspension camp basea on finite element method[J]. Yunnan Electric Power, 2017, 45(5):136-140.
  [11] 曹国文,赵浩.输电线路导线悬垂线夹连接螺栓临时止退装置的研制与应用[J].内蒙古电力技术, 2014, 32(4):78-80. CAO Guowen, ZHAO Hao. Development and Applica-tion on Temporary Backstop Device of Suspension Clamp Connecting Bolt in Transmission Line[J]. Inner Mongolia Electric Power, 2014, 32(4):78-80.
  [12] 姜常胜,马世恩,郑维刚.输电杆塔双独立挂点悬垂线夹结构存在问题的探讨[J].东北电力技术, 2017, 38(11):57-59. JIANG Changsheng, MA Shien, ZHENG Weigang. Dis-cussion on Problems of Transmission Tower of Double Independent Hanging Point in Suspension Clamp[J]. Northeast Electric Power Technology, 2017, 38(11):57-59.
  [13] 王肃,李相栋.500 kV地线悬垂线夹挂轴磨损原因分析[J].电力安全技术, 2020, 22(3):32-34. WANG Su, LI Xiangdong. Cause Analysis for Wear of 500 kV Grounding Suspension Wire Clip Shaft[J]. Elec tric Safety Technology, 2020, 22(3):32-34.
  [14] 全国电力架空线路标准化技术委员会运行分技术委员会.架空输电线路运行规程:DL/T 741-2010[S].北京:中国电力出版社, 2019.